Updated November 2026

Running a well pump on solar power for well pump systems comes down to matching three numbers: the water flow you need, the head height the pump must lift against, and the power the panels can deliver. Get those right and your pump will fill a tank or irrigate a garden without grid power. This guide walks through how to size the system and set it up correctly.

Step 1: Define Your Flow Rate and Head Height

Start with how much water you need per day and how fast you need it delivered. Flow rate is usually measured in gallons per minute (GPM). Head is the total vertical distance the water must climb from the water level in the well to the outlet, plus friction loss in the pipe. A 150-foot static lift with 40 feet of pipe friction gives you a working head of roughly 190 feet, and the pump must be rated for that figure.

Check the pump curve from the manufacturer. It shows how flow drops as head rises. A pump that delivers 5 GPM at 50 feet of head may deliver only 2 GPM at 150 feet, so the curve matters more than the headline rating.

Step 2: Choose a Pump Type That Matches the Power Source

Solar well systems typically use a DC submersible pump or an AC pump driven by a solar inverter. DC pumps connect directly to the panels through a controller and avoid conversion losses, which makes them efficient at moderate heads. AC pumps with a pump-rated inverter handle deeper wells and higher flows but need more panel capacity. Confirm that the pump’s voltage and maximum operating power match your controller and array.

Step 3: Size the Solar Array

Work from the pump’s rated wattage at your operating head, not its nameplate maximum. Add a margin of about 25 percent for cloudy days and panel temperature losses. Panels are rated at standard test conditions, and real output in hot weather is lower. Choose the array’s voltage so it sits within the controller’s input range at the pump’s operating point. Sizing errors at this stage are the most common reason systems underperform.

Step 4: Install and Configure the Controller

  1. Mount panels facing true south in the Northern Hemisphere, tilted near your latitude for year-round use.
  2. Run the DC cable between array, controller and pump with wire sized for the current and distance, to limit voltage drop.
  3. Install a dry-run protection float or pressure switch so the pump shuts off if the water level drops.
  4. Set any minimum-speed or start-voltage settings according to the controller manual.
  5. Add a check valve at the pump outlet and a pressure tank to reduce short cycling.

Solar Well Pump Sizing at a Glance

Working head Typical pump type Sizing focus
Under 100 ft DC submersible Panel wattage at low head
100–200 ft DC or AC with inverter Pump curve at full head
Over 200 ft AC with pump-rated inverter Array voltage and cable run

Common Mistakes to Avoid

  • Sizing panels for the pump’s maximum wattage instead of its output at your real head.
  • Ignoring pipe friction, which can add tens of feet to the working head.
  • Using undersized wire, causing voltage drop and weak pump starts.
  • Skipping dry-run protection in a well that drawdowns during heavy use.
  • Mounting panels where afternoon shade from trees or buildings cuts output.
  • Pump controller: a maximum power point tracking controller matches the array to the pump and improves output in changing light. View on Amazon
  • Pressure tank: smooths out pump cycling and extends motor life. View on Amazon
  • Float switch: prevents dry running when the well level drops. View on Amazon

For more detailed setups, see Solar Well Pump Systems: A Step-by-Step Guide to Sizing and Setup and Can Solar Power Run a Water Pump? Sizing, Limits and Fixes. Owners of off-grid properties often compare options in 3 Best Solar Well Water Pump System Options for Off-Grid Use (2026).

FAQ

Can solar power run a well pump at night?

Not directly. Solar pumps run only when panels produce power, so you need a storage tank to hold water for overnight use. Battery systems are an option but add cost and maintenance.

How many panels do I need for a well pump?

It depends on the pump’s wattage at your working head, plus a margin for weather and heat. Use the pump curve and controller specifications to calculate it, and have a qualified installer check the design for deep or high-flow wells.

Does a solar well pump work on cloudy days?

It runs at reduced speed and output when light is weak. Oversizing the array and using a storage tank help maintain supply during overcast periods.

Conclusion

A solar well pump works reliably when flow rate, working head and array size are matched to each other. Start with your water demand, read the pump curve at your real head, and size the panels with a margin. Consult a licensed installer for electrical work and deep well designs.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our solar water systems guides, checking product details against manufacturer specifications and owner feedback.